德国J.U.M仪器,J.U.M测定器,J.U.M挥发性**物测定器-

Heated Total Hydrocarbon Analyzer, FID Model 3-300A

适用於：　大气中微量碳氢化合物或**浓度测定、烟道气、工厂、无尘室、车辆排放气、 
触媒转化试验；符合EPA Method 25A及Method 503之法规标准
测定原理：F.I.D.火焰离子化方式 

Standard Heated FID Emissions FID Analyzers 

Low Cost Heated FID Analyzer 3-500 



The J.U.M Heated Total Hydrocarbon Analyzer Model 3-500 FID is our lowest cost alternative to continuously measure the total concentration of hydrocarbons within a gaseous sample. This can be ambient air, exhaust gases from a combustion process e.g. stack emissions, from any type of an industrial vent, from an internal combustion engine, or from any other emission containing hydrocarbons. The 3-500 is based on our time proven 300A FID platform of which we have sold thousands of analyzers. 
The 3-500 fully complies with EN 12619, EN 13526 (EU), with 2. BImSchV, 13. BImSchV and 17. BImSchV, (Germany) and with EPA Method 25A and Method 503 (USA). It can be used as a table top instrument but is ideally suited to be integrated in CEMs.

Features

• Made in Germany
• All critical components including pumps, sample filters, detectors and main electronics are manufactured in house
• Fully heated to 190 degree C
• Typical sensitivity 0.01 ppm CH4
• Direct concentration (e.g. ppm) display allows to read up to 3 decade ranges without range change
• Internal sample pump and air pump
• Internal combustion air supply (No external air cylinder needed)
• Very low fuel consumption (less than 20 cc/min @ ** H2)
• Disposable sample filter in rear panel
• Automatic ignite capability (optional)
• Automatic flame out alarm contact and fuel shut off
• Sample pressure regulator not in contact with sample gas
• Multiple range capability, 5 selectable ranges are standard
• 19" rack mount unit, only 132 mm high

Applications

• Stack gases (CEM) and all other Environmental and process applications
• Air and gas scrubber efficiency
• Process chemical gas analysis
• Personnel safety
• Solvent recovery
• Catalytic converter and thermal combustor testing
• Automotive and engine emissions
• Fence line (perimeter) monitoring
• Non-methane hydrocarbon measurements

Methane Only Option 
The available Methane Only Option provides the capability to measure METHANE ONLY or TOTAL HYDROCARBONS. The choice is switch selectable from the front panel or by remote contact closure.

Heated FID Analyzer 3-600

The J.U.M Heated Total Hydrocarbon Analyzer Model 3-600 FID is another low cost alternative to continuously measure the total concentration of hydrocarbons within a gaseous sample. This can be ambient air, exhaust gases from a combustion process e.g. stack emissions, from any type of an industrial vent, from an internal combustion engine, or from any other emission containing hydrocarbons. The 3-500 is built on our time proven 300A FID platform of which we have sold thousands of analyzers. 
The 3-600 fully complies with EN 12619, EN 13526, QAL 1 (EU), with 2. BImSchV, 13. BImSchV and 17. BImSchV, (Germany) and with EPA Method 25A and Method 503 (USA). It can be used as a table top instrument but is ideally suited to be integrated in CEMs.

Features

• Made in Germany

• All critical components including pumps, sample filters, detectors and main electronics are manufactured in house
• Fully heated to 190 degree C
• Equipped with zero and span gas inlets to be selected from internal selector or from remote sources. Auto cal check optional
• Typical sensitivity 0.01 ppm CH4
• 21/2 digit LED display. Optional direct concentration display to read up to 3 decade ranges without range change
• Internal sample pump and air pump
• Internal combustion air supply (No external air cylinder needed)
• Very low fuel consumption (less than 20 cc/min @ ** H2)
• Disposable sample filter in rear panel
• Automatic ignite capability (optional)
• Automatic flame out alarm contact and fuel shut off
• Sample pressure regulator not in contact with sample gas
• Multiple range capability, 5 selectable ranges are standard
• 19" rack mount unit, only 132 mm high

• Stack gases (CEM) and all other Environmental and process applications

Applications

• Air and gas scrubber efficiency
• Process chemical gas analysis
• Personnel safety
• Solvent recovery
• Catalytic converter and thermal combustor testing
• Automotive and engine emissions
• Fence line (perimeter) monitoring
• Non-methane hydrocarbon measurements

Methane Only Option: 
The available Methane Only Option provides the capability to measure METHANE ONLY or TOTAL HYDROCARBONS. The choice is switch selectable from the front panel or by remote contact closure.

Transportable Heated FID 3-800 



The J.U.M 3-800 Portable Heated Total Hydrocarbon Analyzer is a heavy duty FID analyzer to continuously measure the total concentration of hydrocarbons within a gaseous sample. This can be ambient air, exhaust gases from a combustion process e.g. stack emissions, from any type of an industrial vent, from an internal combustion engine, or from any other emission containing hydrocarbons. 
The 3-800 fully complies with EN 12619, EN 13526, QAL 1 (EU), with 2. BImSchV, 13. BImSchV and 17. BImSchV, (Germany) and with EPA Method 25A and Method 503 (USA). It is ideally suited to be used in all stack emissions applications.

Features

• Made in Germany
• All critical components including pumps, sample filters, detectors and main electronics are manufactured in house
• Fully heated to 190 degree C
• Equipped with zero and span gas inlets to be selected from internal selector or from remote sources. Auto cal check optional
• Typical sensitivity 0.01 ppm CH4
• 21/2 digit LED display. Optional direct concentration display to read up to 3 decade ranges without range change
• Internal sample pump and air pump
• Optional 50 liter metal hydrid low pressure fuel storage cartridge, good for 50 hours of uninterrupted measurements
• Very low fuel consumption (less than 20 cc/min @ ** H2)
• Internal combustion air supply (No external air cylinder needed)
• Disposable sample filter in rear panel
• Automatic ignite capability (optional)
• Automatic flame out alarm contact and fuel shut off
• Sample pressure regulator not in contact with sample gas
• Multiple range capability, 5 selectable ranges are standard

Applications

• Stack gas emissions and all other Environmental and process applications
• Air and gas scrubber efficiency
• Process chemical gas analysis
• Personnel safety
• Solvent recovery
• Catalytic converter and thermal combustor testing
• Automotive and engine emissions
• Fence line (perimeter) monitoring

Transportable Heated FID THC / Methane FID Analyzer 3-900 



The J.U.M 3-900 Portable Heated Methane Only and Total Hydrocarbon Analyzer is a heavy duty FID analyzer to continuously measure methane only or the total hydrocarbons to determine the non methane hydrocarbon concentration within a gaseous sample . This can be ambient air, exhaust gases from a combustion process e.g. stack emissions, from any type of an industrial vent, from an internal combustion engine, or from any other emission containing hydrocarbons. 
The 3-900 fully complies with EN 12619, EN 13526, QAL 1 (EU), with 2. BImSchV, 13. BImSchV and 17. BImSchV, (Germany) and with EPA Method 25A and Method 503 (USA). It is ideally suited to be used in all stack emissions applications.

Features

• Made in Germany
• All critical components including pumps, sample filters, detectors and main electronics are manufactured in house
• Fully heated to 190 degree C
• Equipped with zero and span gas inlets to be selected from internal selector or from remote sources. Auto cal check optional
• Typical sensitivity 0.01 ppm CH4
• 21/2 digit LED display. Optional direct concentration display to read up to 3 decade ranges without range change
• Internal sample pump and air pump
• Optional 50 liter metal hydrid low pressure fuel storage cartridge, good for 50 hours of uninterrupted measurements
• Very low fuel consumption (less than 20 cc/min @ ** H2)
• Internal combustion air supply (No external air cylinder needed)
• Disposable sample filter in rear panel
• Automatic ignite capability (optional)
• Automatic flame out alarm contact and fuel shut off
• Sample pressure regulator not in contact with sample gas
• Multiple range capability, 5 selectable ranges are standard

Applications

• Stack gas emissions and all other Environmental and process applications
• Air and gas scrubber efficiency
• Process chemical gas analysis
• Personnel safety
• Solvent recovery
• Catalytic converter and thermal combustor testing
• Automotive and engine emissions
• Fence line (perimeter) monitoring

Light Weight Portable Heated FID THC Analyzer OVF-3000 



The J.U.M OVF-3000 Portable Heated Total Hydrocarbon Analyzer is a light weight, over the shoulder portable heated FID analyzer to continuously measure the total concentration of hydrocarbons within a gaseous sample. This can be ambient air, exhaust gases from a combustion process e.g. stack emissions, from any type of an industrial vent, from an internal combustion engine, or from any other emission containing hydrocarbons. The standard OVF-3000 is equipped with our new low pressure metal hydrid fuel storage system which is good for continuous operation for 50 hours. Fuel Storage can be safely refilled by the user. 
It fully complies with EN 12619, EN 13526, QAL 1 (EU), with 2. BImSchV, 13. BImSchV and 17. BImSchV, (Germany) and with EPA Method 25A and Method 503 (USA). It is ideally suited to be used in all stack emissions applications.

Features

• Light weight, internal fuel storage, easy to operate
• Made in Germany
• All critical components including pumps, sample filters, detectors and main electronics are manufactured in house
• Fully heated to 180 degree C
• Typical sensitivity 0.01 ppm CH4
• 21/2 digit LED display. Optional direct concentration display to read up to 3 decade ranges without range change
• Internal sample pump and air pump
• Optional 50 liter metal hydrid low pressure fuel storage cartridge, good for 50 hours of uninterrupted measurements
• Very low fuel consumption (less than 20 cc/min @ ** H2)
• Internal combustion air supply (No external air cylinder needed)
• Disposable sample filter in front panel
• Automatic flame out alarm contact and fuel shut off
• Sample pressure regulator not in contact with sample gas
• Multiple range capability, 5 selectable ranges are standard

Applications

• Stack gas emissions and all other Environmental and process applications
• Air and gas scrubber efficiency
• Process chemical gas analysis
• Personnel safety
• Solvent recovery
• Catalytic converter and thermal combustor testing
• Automotive and engine emissions
• Fence line (perimeter) monitoring

Wall or Panel Mount Heated FID THC Analyzer W600 



The J.U.M W600 Heated Total Hydrocarbon Analyzer is a very compact wall or panel mount heated FID analyzer to continuously measure the total concentration of hydrocarbons within a gaseous sample. This can be ambient air, exhaust gases from a combustion process e.g. stack emissions, from any type of an industrial vent, from an internal combustion engine, or from any other emission containing hydrocarbons. 
The W600 can easily be wall or panel mounted or can be integrated into a NEMA type enclosure, for example to meet area classifications. It also can be mounted directly on a duct or stack wall. It fully complies with EN 12619, EN 13526, QAL 1 (EU), with 2. BImSchV, 13. BImSchV and 17. BImSchV, (Germany) and with EPA Method 25A and Method 503 (USA). It is ideally suited to be used in all stack emissions applications.

Features

• Made in Germany
• All critical components including pumps, sample filters, detectors and main electronics are manufactured in house
• Fully heated to 190 deg.C
• Equipped with zero and span gas inlets to be selected from internal selector or from remote sources. Auto cal check optional
• Typical sensitivity 0.01 ppm CH4
• 21/2 digit LED display. Optional direct concentration display to read up to 3 decade ranges without range change
• Internal sample pump and air pump
• Internal combustion air supply (No external air cylinder needed)
• Very low fuel consumption (less than 20 cc/min @ ** H2)
• Disposable sample filter in rear panel
• Automatic ignite capability (optional)
• Automatic flame out alarm contact and fuel shut off
• Sample pressure regulator not in contact with sample gas
• Multiple range capability, 5 selectable ranges are standard
• 19" rack mount unit, only 132 mm high

Applications

• Bio gas purifying system monitoring
• Stack gases (CEM) and all other Environmental and process applications
• Air and gas scrubber efficiency
• Process chemical gas analysis
• Personnel safety
• Solvent recovery
• Catalytic converter and thermal combustor testing
• Automotive and engine emissions
• Fence line (perimeter) monitoring.

Heated THC and NMHC FID Analyzers with Permanent Back Purge Sample Filter
Applications

• Stack gas hydrocarbon emissions monitoring
• Fence line monitoring
• Raw exhaust vehicle emissions analysis
• Catalytic converter testing
• Measuring engine combustion efficiency
• Hydrocarbon contamination monitoring in air and other gases
• Carbon adsorption regeneration control
• Detection of trace hydrocarbons in purity gases used in the semi conductor industry
• LEL monitor of solvent laden air

Model VE 7 



Our model VE7 heated FID is being manufactured since 1974 and is the first heated THC analyzer ever built with a permanent back purge sample filter. It is still the most liked heated FID throughout the stack testing community due to its legendary ruggedness, forgivingness and long standing accuracy and sensitivity. The VE7 belongs to the very first total hydrocarbon analyzers being officially certified for compliance in Europe. In the USA, a significant part of the Method 25A was written around the VE7. Many thousand VE7s were sold mainly in Europe and in the USA.
TUV approved and certified for 2. BImSchV. 13. BImSchV and 17. BImSchV, QAL1 certified and fully complies with EN 12619, EN 13526 (EU) and with EPA Method 25A and Method 503 (USA)

Features

• Maintenance free sample filter back purge system allows filter to be cleaned without dismantling (automatic timer optional)
• Built in burner air generator, no external air cylinder needed
• All components in contact with sample fully heated and controlled at 190 degree C
• Built-in sample pressure and sample pumps
• Automatic flame out alarm and contact
• Fast response within 1 second
• Low fuel consumption
• Very selective
• Microprocessor controlled PID-type temperature controller
• Remote control for sample, calibrate and back purge is standard
• Remote or automatic range change optional
•  

Model 3-200



Our transportable model 3-200 fully heated FID is successfully used throughout international markets for over 30 years. Also among other portable gas FIDs, the 3-200 It is the first ever built transportable fully heated FID using our proprietary back purge sample filter. It is widely distributed throughout the industry and the stack testing community and is much liked for its ruggedness, high accuracy, sensitivity and stability. Our optional 50 liter low pressure metal hydride fuel storage can easily be mounted on the left side panel and allows a 45 hour minimum of uninterrupted operation. This fuel storage can be self-refilled at a low pressure of only 25 bar. No special adapter needed. A standard 2-stage pressure regulator with a 30 bar outlet is sufficient

The 3-200 is officially certified to be ** identical to the VE7 and 3-300A analyzers. It is TUV approved and certified for 2. BImSchV. 13. BImSchV and 17. BImSchV and fully complies with EN 12619, EN 13526 (EU) and with EPA Method 25A and Method 503 (USA)

Features

• Maintenance free sample filter back purge system allows filter to be cleaned without dismantling (automatic optional)
• Built in burner air generator, no external air cylinder needed
• All components in contact with sample fully heated and controlled at 190 degree C
• Built-in sample pressure and sample pumps
• Automatic flame out alarm and contact
• Fast response within 1 second
• Low fuel consumption
• Very selective
• Microprocessor controlled PID-type temperature controller
• Remote control for sample, calibrate and back purge is standard
• Remote or automatic range change optional

Model 3-300A 



The 3-300A heated FID was designed in the early 80's as a space saving alternative to our VE7. Also the 3-300A was a "first" in the industry due to its sample filter back purge feature. It is also a very much liked 19" rack mount heated FID throughout the stack testing community and well known for its ruggedness, forgivingness and long standing accuracy and sensitivity. The 3-300A is fully identical to the VE7 and 3-200 and has been officially approved for that.

TüV approved and certified for 2. BImSchV. 13. BImSchV and 17. BImSchV and fully complies with QAL1, EN 12619, EN 13526 (EU) and with EPA Method 25A and Method 503 (USA)

Features

• Maintenance free sample filter back purge system allows filter to be cleaned without dismantling (automatic optional)
• Built in burner air generator, no external air cylinder needed
• All components in contact with sample fully heated and controlled at 190 degree C
• Built-in sample pressure and sample pumps
• Automatic flame out alarm and contact
• Fast response within 1 second
• Low fuel consumption
• Very selective
• Microprocessor controlled PID-type temperature controller
• Remote control for sample, calibrate and back purge is standard
• Remote or automatic range change optional

Model H100



Our HFID Model H100 is a compact heated FID analyzer for high purity hydrogen applications. The H100 measures low trace total hydrocarbon concentration in Hydrogen. For fastest response and highest accuracy except the pressure regulator all components in contact with sample are housed in a 190 deg Celsius heated oven.. The Model H100 is ideally suited for the detection of very low traces of hydrocarbons in pressurized high purity Hydrogen gasses. H100 may also be well suited for the integration in low concentration Hydrogen online inspection systems.

The Model H100 uses a hydrogen flame ionization detector (FID) in a heated oven to prevent the loss of high molecular weight hydrocarbons and to provide long term stability and reliable performance in the analysis of low trace concentration levels of hydrocarbon contaminants in high purity Hydrogen.

Features
 ?      Heated oven FID, low priced, very economical
?Low maintenance
?Excellent long term stability
?Conventional sample back pressure regulator (BPR)
?19-inch slim line design, 132mm high
?Automatic flame out indicator with automatic fuel shut off valve
?Fast response
?Low fuel and air consumption
?Very selective
?All heated components in oven, except BPR
?Microprocessor PID-type temperature controller for FID-oven  

Applications
 ?Detection of low trace hydrocarbon levels in high purity Hydrogen Gas
?Online inspection of high purity Hydrogen plumbing systems as used in the semiconductor industry

?Online monitoring on loading terminals for hydrocarbon contamination in Hydrogen

Model 5-100



Our 5-100 is a compact heated FID analyzer for high purity  gases applications. The H100 measures low trace total hydrocarbon concentration in CO2, Argon, Helium, Nitrogen N2O and many other technical gases. For fastest response and highest accuracy  all components in contact with sample are housed in a 190 deg Celsius heated oven, except the pressure regulator. The Model 5-100 is ideally suited for the integration in low concentration semiconductor gases online inspection systems. 
The 5-100 uses a hydrogen flame ionization detector (FID) in a heated oven to prevent the loss of high molecular weight hydrocarbons and to provide long term stability and reliable performance in the analysis of low trace concentration levels of hydrocarbon contaminants in high purity Hydrogen.

Features
?Heated oven FID, low priced, very economical
?Low maintenance
?Excellent long term stability
?Conventional sample back pressure regulator (BPR)
?19-inch slim line design, 132mm high
?Automatic flame out indicator with automatic fuel shut off valve
?Fast response
?Low fuel and air consumption
?Very selective
?All heated components in oven, except BPR
?Microprocessor PID-type temperature controller for FID-oven  
 Applications
?Detection of low trace hydrocarbon levels in high purity industrial gases
?Online inspection of high purity gas plumbing systems as used in the semiconductor industry
?Online monitoring on loading terminals for high purity industrial gases

Heated FID Analyzer for FTIR based CEM's, 3-700

The J.U.M Heated Total Hydrocarbon Analyzer Model 3-700 FID is designed to be installed directly upstream of a FTIR analyzer (e.g. Gasmet) to continuously measure the total concentration of hydrocarbons within a gaseous sample. All controls which allow to calibrate the FTIR or FID individually are built in. Sources can be ambient air, exhaust gases from a combustion process e.g. stack emissions, from any type of an industrial vent, from an internal combustion engine, or from any other emission containing hydrocarbons.  
The 3-700 fully complies with EN 12619, EN 13526, QAL 1 (EU), with 2. BImSchV, 13. BImSchV and 17. BImSchV, (Germany) and with EPA Method 25A and Method 503 (USA). It can be used as a table top instrument but is ideally suited to be integrated in CEMs.

Features
?Made in Germany
?All critical components including pumps, sample filters, detectors and main electronics are manufactured in house
?Fully heated to 190 degree C
?Equipped with zero and span gas inlets to be selected from internal selector or from remote sources. Auto cal check optional
?Typical sensitivity 0.01 ppm CH4
?21/2 digit LED display. Optional direct concentration display to read up to 3 decade ranges without range change
?Internal sample pump and air pump
?Internal combustion air supply (No external air cylinder needed)
?Very low fuel consumption (less than 20 cc/min @ ** H2)
?Disposable sample filter in rear panel  
?Automatic ignite capability (optional)
?Automatic flame out alarm contact and fuel shut off
?Sample pressure regulator not in contact with sample gas
?Multiple range capability, 5 selectable ranges are standard
?19" rack mount unit, only 132 mm high 
Applications:
 ?Stack gases (CEM) and all other Environmental and process applications
?Air and gas scrubber efficiency
?Process chemical gas analysis
?Personnel safety
?Solvent recovery
?Catalytic converter and thermal combustor testing
?Automotive and engine emissions
?Fence line (perimeter) monitoring

Model VE572



The HFID Model VE572 is a reliable and rugged Dual Channel Sequencing heated total hydrocarbon analyzer for low drift, high accuracy, sensitivity and stability. It uses our time proven hydrogen flame ionization detector (FID) in a heated oven to prevent the loss of high molecular weight hydrocarbons and to provide reliable performance in the analysis of high concentrations down to trace levels of THC -contaminants in high purity gases, air and other gases.
All sample wetted components are integrated into the heated chamber. The two permanent heated sample filters are designed to be fully regenerated by back purging with compressed air or nitrogen. With only a few seconds needed for back purging, this technique allows uninterrupted measurements during cleaning of the sample filter while not in the sample mode. During back purging the sample filter, the sample line is also cleaned. The use of a stack probe filter is not necessary.
The combustion air supply for the detector is built in. No expensive zero gas generator or external cylinder for synthetic air is needed. Automated sample sequencing and back purging of the sample filter can be done with one of our optional timing controllers.
 
Features  
?All components in contact with sample are fully heated and controlled at 190 degC
?Built-In sample pressure and sample pumps  
?Built-in combustion air supply, no extra burner air bottle needed  
?Maintenance free sample filter backpurge system allows both filters to be cleaned without dismantling (automatic purge optional)  
?Permanent heated 2 micron stainless steel mesh filter  
?"Overflow" calibration system for pressure less zero/span calibration  
?Automatic flame out control with alarm. An automatic fuel shut off valve is optional  
?Fast response less than 1 second
?Low fuel consumption and very selective
?Microprocessor PID-type temperature controller  
?Cold spot free coupling of the heated sample lines inside the heated oven optional
?Remote control for sample, zero/span and backpurge is standard
?Automatic or remote range change optional
Applications
?EPA Method 25A compliance monitoring of source hydrocarbons (inlet and outlet)
?Stack gas hydrocarbon emissions monitoring before and after an abatement system
?Solvent recovery monitor for carbon bed break through
?Thermal combustor compliance monitoring and testing
?Catalytic converter compliance monitoring and testing
?Carbon adsorption regeneration control
?Measuring engine combustion efficiency
?Raw exhaust vehicle emissions analysis
?Hydrocarbon contamination monitoring in air and other gases
?Carbon adsorption regeneration control